Products Range

 

Rotary Controls

rotary_1

GA01 GA02 GA05

Gravity position indicators

Bezel :AISI 303 stainless steel.
Case :
Zinc-plated steel.


Click here to view more information
rotary_2

GA11 GA12

Gravity positionindicators

Bezel :Technopolymer. Moulded over the window.
Case :
Glass-fibre reinforced polyamide based (PA) technopolymer. Moulded-in spindle. Resistant to solvents, oils, greases and other chemical agents.


Click here to view more information
rotary_3

MBT-GA

Knobs with integral gravity position indicator

Bezel :Technopolymer. Moulded over the window.
Colour :
Black, matte finish.


Click here to view more information
7387_GW12_p_i

GW12

Digital-analogue gravity position indicators

Bezel :
Technopolymer. Moulded over the window.
Case :
Glass-fibre reinforced polyamide based (PA) technopolymer.
Moulded-in spindle.
Resistant to solvents, oils, greases and other chemical agents.


Click here to view more information
8638_MBT-GW_p_i

MBT-GW

Knobs with integraldigital-analoguegravity position indicator

Bezel :
Technopolymer. Moulded over the window.
Colour :
Black, matte finish.


Click here to view more information
7582_PA01_PA02_PA05_p_i

PA01 PA02 PA05

Positive drive indicators

Bezel :
AISI 303 stainless steel.
Case :
Zinc-plated steel.


Click here to view more information
7583_PA11-PA12_p_i

PA11 PA12

Positive drive indicators

Bezel :
Technopolymer. Moulded over the window.
Case :
Glass-fibre reinforced polyamide based (PA) technopolymer.
Moulded-in spindle.
Resistant to solvents, oils, greases and other chemical agents.


Click here to view more information
7873_PW12_p_i

PW12

Digital-analogue positive drive indicators

Bezel :
Technopolymer. Moulded over the window.
Case :
Glass-fibre reinforced polyamide based (PA) technopolymer.
Moulded-in spindle.
Resistant to solvents, oils, greases and other chemical agents.


Click here to view more information
7456_IZN__p_i

IZN-XX

Knurled grip knobs for position indicators

Accessories on request :
Cover type CP. for fitting instead of the indicator.
Assembly :
Black-oxide steel boss, H7 reamed hole, fitting to shaft by means of a supplied grub screw with hexagon socket and cup end UNI 5929-85.


Click here to view more information
9759_MBT-XX_(new)_p_i

MBT-XX NEW

Diamond cut knurled knobs for position indicators

Accessories on request :
Cover type CP-XX for fitting instead of the indicator.
Colour :
Black, matte finish.


Click here to view more information
7714_VHT__VHT_INOX_p_i

VHT-XX

Lobe knobs for position indicators

Accessories on request :
Cover type CP.XX for fitting instead of the indicator.
Colour :
Black, matte finish.


Click here to view more information
9750_VC_792-XX_p_i

VC.792-XX

Lobe knobs for position indicators

Accessories on request :
Cover type CP-XX for use without the indicator.
Colour :
Black, matte finish.


Click here to view more information
7726_VRTP__VRTP+I_p_i

VRTP-XX

Two-spoke handwheels for position indicators

Colour :
Black, matte finish.
Indicator choice (to be ordered separately) :
VRTP-XX two-spoke handwheels can be used with analogue and digital-analogue gravity indicators. To choose the indicator see the table below for possible assembly indicators.
See also “Assembly instructions” for gravity indicators.


Click here to view more information
7694_VD+I_p_i

VD-XX

Solid handwheels with revolving handle for position indicators

Colour :
Black, glossy finish.
Indicator choice (to be ordered separately) :
VD-XX solid handwheels can be used with analogue gravity indicators type GA05.
See also “Assembly instructions” with gravity indicators.


Click here to view more information
7696_VDC__VDC+I_p_i

VDC-XX

Solid handwheels for position indicators

Assembly :
Black-oxide steel hub.
– VDC-GXX: for gravity indicators.
Not drilled hub, see table for maximum permissible boring diameters d’ and d”.
-VDC-GXX+I: for gravity indicators.
Not drilled hub, see table for maximum permissible boring diameters d’ and d”.
Type I.301+x revolving handle in Duroplast, black colour, glossy finish.
– VDC-PXX+I: for positive drive indicators.
Rear flange with internal crown gear wheel in acetal resin based (POM) technopolymer. Black-oxide steel screw and anchor pin.
Hub with H7 reamed throught hole.
Type I.301+x revolving handle in Duroplast, black colour, glossy finish.
Colour :
Black, glossy finish.


Click here to view more information
7824_VDSC-XX_p_i

VDSC-XX

Solid handwheels for position indicators

Accessories on request :
Cover type CP-XX for fitting instead of the indicator.
Colour :
Black, matte finish.


Click here to view more information
7223_EWW+IEL_p_i

EWW-XX

Steering handwheel with revolving handle for position indicators

Accessories on request :
– Axial retaining washer type GN 184.
– Cover type CP-XX for fitting instead of the indicator.
Colour :
Grey-black, matte finish.


Click here to view more information
7652_VAD__VAD+I_p_i

VAD-XX

Solid handwheels for position indicators

Colour :
Black, matte finish.
Indicator choice (to be ordered separately) :
To choose the indicator see the table below for possible assembly with indicators. See also “Assembly instructions” for gravity indicators type G or positive drive indicators type P.


Click here to view more information
7122_CP__p_i

CP-XX

Covers

Applications :
CP-XX covers are suitable for closing the indicator housing when the indicator is not required.
Assembly :
Push-fit. The cover can be removed by using a screwdriver in the proper cavity.


Click here to view more information
7598_SC__p_i

SC-XX

Indicator housings

Colour :
Black, matte finish.
Features and applications :
SC-XX indicator housings are suitable with gravity indicators on any handwheels or other control devices.


Click here to view more information
8502_DD50_p_i

DD50

Direct drive digital position indicators mini series

Accessories on request (to be ordered separately) :
RB50: black-oxide steel reduction sleeves (see table).
Assembly instructions :
1. Drill a Ø 6 mm by 10 mm hole in the body of the machine with a 18 mm centre distance from the spindle to fit the rear referring pin.
2. Set the spindle to the start or referring position.
3. Fit the indicator with the zeroed roller counter onto the spindle and make sure that the referring pin fit the hole.
4. Clamp the bushing to the spindle by tightening the grub screw with hexagon socket and cup end, according to UNI 5929-85.


Click here to view more information
7134_DD51_p_i

DD51

Direct drive digital position indicators

Accessories on request (to be ordered separately) :
GN 954.6: zinc die-cast bases for spindle locking, epoxy resin coating, black colour, matte finish (see table). Type GN 302 adjustable handle. GN 954.6 locking bases allow an easy and quick locking of the spindles after their positioning. They are equipped with a Ø 6.1 mm to fit the referring pin of the indicator. They can be assembled with the handle either on the right or on the left and can be fitted to the machine by means of two M4 cylindrical head screws (not included in the supply).
BS51: glass-fibre reinforced polyamide based (PA) technopolymer spacer plate (code CE.85900).
MD51: polyamide based (PA) technopolymer fluted grip control knob.
RB51: black-oxide steel reduction sleeves (see table).
Assembly instructions :
1. Drill a Ø 6 mm by 10 mm hole in the body of the machine with a 22 mm centre distance from the spindle to fit the rear referring pin.
2. Set the spindle to the start or referring position.
3. Fit the indicator with the zeroed roller counter onto the spindle and make sure that the referring pin fit the hole.
4. Clamp the bushing to the spindle by tightening the grub screw with hexagon socket and cup end, according to UNI 5929-85.


Click here to view more information
7950_DD52R_p_i

DD52R

Direct drive digital position indicator

Accessories on request (to be ordered separately) :
GN 953.6: zinc die-cast bases for spindle locking, epoxy resin coating, black colour, matte finish (see table). Type GN 302 adjustable handle. GN 953.6 locking bases allow an easy and quick locking of the spindles after their positioning. They are equipped with a Ø 6.1 mm hole to fit the referring pin of the indicator. They can be assembled with the handle either on the right or on the left and can be fitted to the machine by means of two M5 cylindrical-head screws (not included in the supply).
BS52R: glass-fibre reinforced polyamide based (PA) technopolymer spacer base (code CE.83950), designed with two pre-drilled holes for UNI 10227 self-tapping screws Ø 2.2 (not included in the supply).
RB52: black-oxide steel reduction sleeves (see table).
PE.6-10: red technopolymer anti-rotation pin (code CE.83960).
Assembly instructions :
1. Drill a Ø 6 mm by 10 mm hole in the body of the machine with a 30 mm centre distance from the spindle to fit the rear referring pin.
2. Set the spindle to the start or referring position.
3. Fit the indicator with the zeroed roller counter onto the spindle and make sure that the referring pin fit the hole.
4. Clamp the bushing to the spindle by tightening the grub screw with hexagon socket and cup end, according to UNI 5929-85.


Click here to view more information
9257_MPI-15_p_i

MPI-15

Magnetic length and angle measuring system


Click here to view more information
9668_DD51-E_p_i

DD51-E

Direct drive electronic position indicators with battery power supply

Accessories on request (to be ordered separately) :
AISI 304 stainless steel RB51 reduction sleeves.
Assembly instructions :
1. Drill a Ø 6×10 mm hole in the body of the machine with a 22 mm centre distance from the shaft to fit the rear referring pin.
2. Fit the indicator onto the shaft and make sure that the referring pin fit the hole.
3. Clamp the bushing to the shaft by tightening the grub screw with hexagon socket and cup end, according to UNI 5929-85.


Click here to view more information
9826_DD52R-E_p_i

DD52R-E

Direct drive electronic position indicators with battery power supply

Accessories on request (to be ordered separately) :
AISI 304 stainless steel RB52 reduction sleeves.
Assembly instructions :
1. Drill a Ø 6×10 mm hole in the body of the machine with a 30 mm centre distance from the shaft to fit the rear referring pin.
2. Fit the indicator onto the shaft and make sure that the referring pin fit the hole.
3. Clamp the bushing to the shaft by tightening the grub screw with hexagon socket and cup end, according to UNI 5929-85.


Click here to view more information
7808_DE51_p_i

DE51

Direct driveabsolute opticalelectronic position indicators

Accessories on request (to be ordered separately) :
Connection cables between PLC or central memory unit and DE51 or
between two DE51 with different lenghts (see table “Cables and accessories”)
Terminal resistor to avoid noises and interferences on the net (see table “Cables and accessories”)
RB51: black-oxide steel reduction sleeves (see table)
MD51: polyamide based (PA) technopolymer fluted grip control knob.
Assembly instructions :
1. Drill a Ø 6 mm by 10 mm hole in the body of the machine with a 22 mm centre distance from the spindle to fit the rear referring pin.
2. Set the spindle to the start or referring position.
3. Fit the indicator onto the spindle and make sure that the referring pin fit the hole.
4. Clamp the bushing to the spindle by tightening the grub screw with hexagon socket and cup end, according to UNI 5929-85.
5. Network the indicator using cables with connectors type M8-4PIN (see table “Mechanical and electrical characteristics”).


Click here to view more information
7777_MD51_p_i

MD51

Fluted grip knob for digital indicators DD51 and DE51

Applications :
MD51 knob has been designed to be mounted on DD51 direct drive digital position indicatorsor on DE51 direct drive electronic position indicators.
Assembly instruction :
1. Remove the grub screw from the indicator bushing.
2. Insert MD51 knob making sure that the grub screw seat matches the tapped blind hole of the indicator bushing.
3. Screw the grub supplied with the knob, to lock simultaneously the spindle, the indicator bushing and the knob.


Click here to view more information
9440_GN_953_6_p_i

GN 953.6

Locking bases

Accessories on request (to be ordered seperately) :
GN 953.6 locking bases allow an easy and quick locking of the spindles after their positioning. They are equipped with a Ø 6 mm to fit the referring pin of the indicator. They can be assembled with the handle either on the right or on the left and can be fitted to the machine by means of two M4 / M5 cylindrical head screws (not included in the supply).
Adjustable handle GN 302 :
– Lever body, zinc alloy die-cast, RAL 9005 black matte finish, epoxy resin coating.
– Black-oxide steel threaded stud with toothed element for coupling to the lever body, treated steel retaining screw and return spring.


Click here to view more information
9441_GN 954.6_p_i

GN 954.6

Locking bases

Adjustable handle GN 302 :
– Lever body, zinc alloy die-cast, RAL 9005 black matte finish, epoxy resin coating.
– Black-oxide steel threaded stud with toothed element for coupling to the lever body, treated steel retaining screw and return spring.
Features and applications :
GN 954.6 locking bases allow an easy and quick locking of the spindles after their positioning. They are equipped with a Ø 6 mm to fit the referring pin of the indicator. They can be assembled with the handle either on the right or on the left and can be fitted to the machine by means of two M4 / M5 cylindrical head screws (not included in the supply).


Click here to view more information